Dacia Duster wiring harness replacement — Mk1–Mk2, 2010–2024

Harness assemblies we build for the Dacia Duster

Each assembly is a separate part number with its own drawing and test fixture, so you can order the complete set or replace one failed loom. All five share the same splice points as the factory harness.

Assembly	Build specification
Engine & ECU harness	Firewall-to-engine routing with injector, coil, O2, cam and crank branches, sealed ECU header and the OEM connector series retained so the loom plugs in without re-pinning.
Body / cabin harness	Main body loom carrying the fuse and relay block, BCM connectors, interior lighting, audio, immobilizer and convenience circuits on the original circuit count.
Chassis, ABS & suspension harness	Wheel-speed, ABS/ESP sensor, ride-height and fuel-tank branches in abrasion-resistant conduit with sealed sensor connectors.
Lighting & front-end harness	Headlamp, fog, horn, washer and front-sensor branches with sealed, keyed connectors.
Door & window harness	Door-grommet section built on flex-rated cable with window-motor, lock-actuator and mirror connectors.

Fitment

Chassis / generation	HS / HM (Mk1–Mk2)
Production years	2010–2024
Engine variants	1.6 16V K4M · 1.5 dCi K9K · 1.0 TCe · 1.3 TCe
Main markets	Europe, LATAM, MEA, India
Body styles	Compact SUV
Order basis	OEM part number, VIN, or physical sample

Known failure points on high-mileage Dusters

These are the faults that bring Duster owners to us. If your symptom matches one of them, the loom — not the component — is usually the cause, and a section replacement is often enough.

• Dust and moisture in the engine-bay connector block
• K9K injector loom failure
• Rear ABS harness chafe on rough-road markets
• Door loom fatigue on high-mileage taxi examples

How we build it

• Drawing first. We map your sample or OEM drawing into a circuit list, connector list and 2D layout, and send it for approval before production.
• Connector parity. The original connector series is retained for the HS / HM (Mk1–Mk2) so the loom plugs into the existing ECUs, BCM and sensors without adapters or re-pinning.
• Wire spec matched to the branch. 0.35–0.5 mm² for signal, 1.0–2.5 mm² for lighting and motors, 4–6 mm² for feeds, with heat-rated insulation on engine-bay runs.
• 100% test. Continuity, short and pin-out test against the drawing; hipot where HV is involved; bend test on hinge loops. Test record ships with the carton.

Specifications

Wire	TXL / GXL stranded copper, 0.22–6 mm² (AWG 24–10)
Connectors	Sumitomo, Yazaki, Aptiv, TE, Molex, KET — original series or documented equivalent
Protection	Tape, corrugated conduit, heat-shrink breakouts, grommets, sealed pass-throughs
Temperature	-40 °C to +125 °C continuous, +150 °C engine-bay branches
Testing	100% continuity & pin-out · crimp pull test · bend test · salt spray on chassis runs
MOQ	50 sets per part number, 1 unit for a paid sample
Lead time	25–30 days production · 7–10 days sample
Warranty	24 months / 50,000 km against manufacturing defect

Dacia Duster harness questions

What does a full wiring harness for a Dacia Duster cost?

A complete set for a Dacia Duster (HS / HM (Mk1–Mk2), 2010–2024) typically runs USD 320–1,450 depending on circuit count, connector count and whether HV sections are included. A single engine or body assembly is USD 120–520. Send the OEM part number and a photo of the label for an exact figure — quotes are issued within 24 hours.

Can you supply a Dacia Duster harness when the factory part is discontinued?

Yes. For discontinued Dacia Duster looms we rebuild from your original harness: we map every circuit, identify the connector families and produce a new drawing. This is the standard route for the HS / HM (Mk1–Mk2) generation now that dealer stock has dried up in most markets.

What is the lead time and MOQ for a Dacia Duster harness?

Sample in 7–10 days after drawing approval, production in 25–30 days. MOQ is 50 sets per part number, with one unit accepted for a paid sample. Repeat orders on an approved drawing are faster because the test fixture is already built.